USB2.0 OTG PHY supporting UTMI+ level 3 interface - 28HK/55LL
New Lattice Mixed Signal Software Design Tool Supports Automotive Versions of Power Manager II Devices
All Power Manager and ispClock Devices Also Supported
HILLSBORO, OR - AUGUST 18, 2008 - Lattice Semiconductor (NASDAQ: LSCC) today announced the release of its PAC-Designer® software design tool suite, version 4.99a. The tool suite now supports Lattice’s AECQ100-qualified automotive Power Manager II (LA-ispPAC®-POWR1014/A) devices. The PAC-Designer tool suite also provides easy to use, point-and-click, intuitive design and verification support for all Power Manager and ispClock™ mixed signal devices.
“Today’s automotive designs use advanced CPUs, FPGAs and ASICs, which increases the number of board-mounted power supplies,” said Stan Kopec, Lattice corporate vice president of marketing. “Using Lattice’s PAC-Designer software tools, designers can quickly implement and fine tune the power management algorithm used to control and monitor these diverse power supplies. The resulting board-specific power management design is more accurate, requires less circuit board area and costs less than traditional designs using multiple off-the-shelf dedicated devices.”
The Benefits of PAC-Designer Software
Common power management functions found on circuit boards include hot-swap control, voltage supervision, supply sequencing and reset generation. To ensure board reliability, all board-mounted power supplies should be sequenced and monitored via a power management algorithm. Typically, the power management algorithm is either changed or fine tuned during the board debug process to meet unforeseen device power-up behavior. Traditional solutions are hard-wired and cannot be changed without an expensive board re-spin. Lattice’s Windows-based PAC-Designer software enables implementation of a new power management algorithm in Lattice’s Power Manager II devices within minutes.
Similarly, clock network designs require timing adjustments during the board debug phase. The Lattice ispClock devices support an in-system programmable skew mechanism. Using the PAC-Designer software, designers can precisely alter the clock skew of each of the clock nets. Traditionally, clock skew has been implemented by “snaking” clock traces on the board, and any change to the skew was implemented through a time consuming, expensive board re-spin. Using the PAC-Designer software, the clock network skew is altered simply by reprogramming the ispClock device.
Pricing and Availability
The PAC-Designer software is available now and can be downloaded free of charge from the Lattice website, www.latticesemi.com.
About Lattice Automotive Power Manager II Devices
The Lattice Automotive Power Manager II device family includes the LA-ispPAC-POWR1014 and LA-ispPAC-POWR1014A. The LA-ispPAC-POWR1014 device integrates a 24 macrocell PLD and 10 analog voltage monitoring inputs, each with dual precision voltage monitoring comparators with an accuracy of 0.3%. In addition, the LA-ispPAC-POWR1014A device integrates a 10-bit Analog to Digital Converter (ADC) for voltage measurements and an I2C interface that enables a microcontroller or processor to read the status of all the comparators, inputs as well as outputs. Both the POWR1014 and POWR1014A devices have been ruggedized to operate across a wide range of power supply voltages, from 2.8V to 3.9V.
About Lattice ispClock Devices
There are two programmable Lattice ispClock families: the ispClock5600A family (in-system programmable zero-delay clock generation and distribution) and the ispClock5300S family (in-system programmable zero-delay clock distribution). Users can standardize on these devices across a wide variety of designs instead of using a separate set of single-function clock devices on each board design.
The ispClock5600A devices provide seven on-chip counters for the generation of up to 5 clock frequencies. The E2CMOS®-based ispClock5600A device can source up to 20 clock outputs, each with independently programmable output skew, I/O standard and frequency selection.
The ispClock5300S devices integrate a zero-delay buffer and fan-out buffers with independently programmable skew, I/O standard and output termination impedance.
About Lattice Semiconductor
Lattice Semiconductor Corporation provides the industry’s broadest range of Programmable Logic Devices (PLD), including Field Programmable Gate Arrays (FPGA), Complex Programmable Logic Devices (CPLD), Mixed-Signal Power ManagementClock Generation Devices, and industry-leading SERDES products.
Lattice continues to deliver “More of the Best” to its customers with comprehensive solutions for system design, including an unequaled portfolio of high-performance, non-volatile and low-cost FPGAs.
Lattice products are sold worldwide through an extensive network of independent sales representatives and distributors, primarily to OEM customers in communications, computing, industrial, consumer, automotive, medical and military end markets. For more information, visit http://www.latticesemi.com
|
Related News
- Lattice Mixed-Signal Power Manager Devices Will Simplify Thales' System Design
- Lattice FPGAs with High I/O Density Bring Low Power Signal Bridging and Interface Management to Edge Devices
- Lattice Announces New Version Of Mixed Signal Design Software
- Lattice Ships 15 Million Power Manager Devices
- Lattice Launches Power & Platform Management Seminars and Lowers Price of Evaluation Boards and Platform Manager Devices
Breaking News
- Logic Design Solutions launches Gen4 NVMe host IP
- ULYSS1, Microcontroller (MCU) for Automotive market, designed by Cortus is available
- M31 is partnering with Taiwan Cooperative Bank to launch an Employee Stock Ownership Trust to strengthen talent retention
- Sondrel announces CEO transition to lead next phase of growth
- JEDEC Publishes LPDDR5 CAMM2 Connector Performance Standard
Most Popular
- Arm's power play will backfire
- Alphawave Semi Selected for AI Innovation Research Grant from UK Government's Advanced Research + Invention Agency
- Secure-IC obtains the first worldwide CAVP Certification of Post-Quantum Cryptography algorithms, tested by SERMA Safety & Security
- Weebit Nano continuing to make progress with potential customers and qualifying its technology Moving closer to finalisation of licensing agreements Q1 FY25 Quarterly Activities Report
- PUFsecurity Collaborate with Arm on PSA Certified RoT Component Level 3 Certification for its Crypto Coprocessor to Provide Robust Security Subsystem Essential for the AIoT era
E-mail This Article | Printer-Friendly Page |